Disk Detector
Windows 10 & 11 Buy license · $29.95
Missing drives

Hard Drive Disappeared After a Windows Update: How to Get It Back

Hard drive disappeared after Windows update? Restore the missing drive letter, driver or storage setting, and check whether your files are still there.

Updated 5 minute read The Disk Detector team

If a hard drive disappeared after a Windows update, the drive and your files are almost always still there. The update has usually removed the drive letter, set the disk offline, or swapped in a different storage driver. Open Disk Management first: if the drive is listed, assign a letter or bring it online and it will reappear in File Explorer. If it is not listed, check Device Manager for a driver problem and roll the driver back. Only uninstall the update if those fixes do not work.

Work through the steps below in order. None of them touch the data on the drive, and the one step that could is clearly marked.

Why updates make drives vanish

What changedWhat you seeFix
Drive letter removed or reassignedDrive in Disk Management, missing from File ExplorerAssign a drive letter
Disk set offlineDisk Management shows OfflineBring it online
Storage or chipset driver replacedDrive missing from Disk Management, or a warning in Device ManagerRoll back or reinstall the driver
BitLocker or device encryption turned onDrive shows a padlock and asks for a keyUnlock with the recovery key
Firmware or power setting changedDrive missing after a restart, returns after a full shutdownTurn off Fast Startup, check BIOS

Step 1: Look in Disk Management

  1. Right-click Start and choose Disk Management.
  2. Look through the disks in the lower half for one that matches your missing drive's size.
  3. Read its disk status (left box) and volume status (right boxes).

If the drive is there, you are one or two clicks from fixing it. If it is not listed at all, go to Step 4. Our guide to Disk Management status meanings explains every label you might see.

If Disk Management shows the drive as Not Initialized or its partition as RAW or Unallocated after an update, do not initialize or format it. Those actions can erase the information needed to get your files back. Stop and recover your files first.

Step 2: Assign the drive letter again

This is the most common cause, especially for second internal drives and partitions.

  1. In Disk Management, right-click the partition (the colored box, not the gray disk box).
  2. Choose Change Drive Letter and Paths.
  3. Click Add, choose a letter, and click OK.

The drive should appear in File Explorer straight away. If programs or shortcuts expected a particular letter, such as D:, assign that letter so they work again. If that letter is now used by something else, such as a card reader or DVD drive, change that device's letter first. Our guide on how to assign a drive letter in Windows covers the details, including the command-line method.

Step 3: Bring the disk online

If the gray disk box says Offline, right-click it and choose Online. If it comes back offline after every restart, or shows "The disk is offline because of policy set by an administrator", the Windows SAN policy is keeping it offline. You can bring it online with diskpart:

  1. Open Terminal (Admin) and type diskpart.
  2. Type list disk and find your drive by size.
  3. Type select disk 1, using your disk's number.
  4. Type online disk, then attributes disk clear readonly if it is read-only.

These commands do not change the data on the disk. Our guide to the disk offline policy set by administrator error explains how to make the change stick.

Step 4: Check the storage driver

If the drive is not in Disk Management at all, the update may have replaced the driver for your storage controller. This is more common on PCs with Intel Rapid Storage Technology or RAID settings, and with some NVMe drives.

  1. Right-click Start and choose Device Manager.
  2. Expand Disk drives. If your drive is listed, it is detected and the problem is in Windows' storage setup.
  3. Expand Storage controllers and IDE ATA/ATAPI controllers. Look for a yellow warning triangle.
  4. Right-click the controller with a warning, or the one that was updated, choose Properties → Driver and click Roll Back Driver if it is available.
  5. Restart the PC.

If Roll Back Driver is grayed out, download the storage or chipset driver for your exact PC or motherboard model from the manufacturer's support page and install it. Click Action → Scan for hardware changes in Device Manager afterward.

Step 5: Rule out encryption and power settings

  • Padlock on the drive icon: BitLocker or device encryption is active. Double-click the drive and enter the password, or use the BitLocker recovery key, which is often saved to your Microsoft account when device encryption is turned on.
  • Drive returns after Shut down + restart but not after a normal shutdown: Fast Startup may be leaving the drive in a bad state. Turn it off under Control Panel → Power Options → Choose what the power buttons do, click Change settings that are currently unavailable and untick Turn on fast startup.
  • Drive missing from the BIOS too: the update is a coincidence. The problem is the drive, cable or power. See hard drive not showing in BIOS.

Step 6: Uninstall the update as a last resort

If the drive vanished right after a specific update and nothing above helps, remove that update: Settings → Windows Update → Update history → Uninstall updates. Pick the most recent one, uninstall and restart. Windows may reinstall it later, so treat this as a way to confirm the cause and get to your files, then check the PC maker's site for an updated driver.

Find the cause faster

Each of the checks above lives in a different part of Windows. Disk Detector looks for every drive connected to your PC, including ones File Explorer will not show, and tells you exactly why a drive is hidden: no drive letter, offline, not initialized, unallocated, an unreadable file system, a driver problem or not detected at all. Safe fixes like assigning a drive letter run in one click, and anything that could affect data is clearly marked first.

Once the drive is back, it is worth checking its health while you are there. A drive that disappears for no reason, rather than after an update, can be an early sign of a failing disk or cable, and Disk Detector's SMART check will tell you which.

Prevent it next time

  • Keep a backup of anything on your second drive. Updates rarely touch data, but drives do fail.
  • Note which drive letters your drives use so you can restore them quickly.
  • Install storage drivers from your PC maker after major Windows feature updates if you use RAID or Intel RST.

Frequently asked questions

Did the update delete my files?

Almost never. The drive is usually still there but has lost its drive letter or driver.

Can I roll back the update?

Yes, under Settings, Windows Update, Update history, Uninstall updates, but try the drive letter and driver fixes first.

Why do storage drivers change in updates?

Windows Update can install a newer or generic storage or chipset driver, which occasionally changes how drives are detected.

Get three guides like this every month, plus software update notices.Subscribe →