Disk Detector
Windows 10 & 11 Buy license · $29.95
Missing drives

New SSD Not Showing Up in Windows? How to Get It Detected

New SSD not showing up in Windows 10 or 11? Initialize it, check BIOS and M.2 slot settings, and fix NVMe and SATA detection problems step by step.

Updated 5 minute read The Disk Detector team

If your new SSD is not showing up in Windows, the most likely reason is that it has not been initialized. A brand new SSD has no partition table, so File Explorer has nothing to show until you initialize it and create a volume in Disk Management. If the SSD is not in Disk Management either, the problem is lower down: the drive is not seated properly, the M.2 slot does not support it, a slot is disabled by the motherboard, or a storage driver is missing. The eight fixes below cover all of these, starting with the most common.

These steps apply to SATA SSDs, M.2 SATA SSDs and NVMe SSDs on Windows 10 and Windows 11.

First, find where the SSD is missing

Open Disk Management by pressing Win + X and choosing Disk Management. Then decide which case you are in:

  • The SSD is in Disk Management but not File Explorer: start with fixes 1 to 3. These are quick and solve most new-drive problems.
  • The SSD is not in Disk Management: skip to fixes 4 to 8, which deal with hardware, firmware and drivers.

Fixes when the SSD is in Disk Management

Fix 1: Initialize the new SSD

When you open Disk Management with a new drive installed, Windows usually pops up an Initialize Disk window. If it does not, find the disk marked Unknown, Not Initialized, right-click its label on the left, and choose Initialize Disk.

  1. Make sure only the new disk is ticked.
  2. Choose GPT (GUID Partition Table). This is right for almost every modern PC and is required for disks larger than 2 TB.
  3. Click OK.

Only initialize an SSD that is new or empty. If this SSD was working before and has files on it, initializing writes a new partition table and your files will no longer be found. Read our guide to fixing a disk that shows Unknown, Not Initialized first.

Fix 2: Create a volume

After initializing, the SSD shows as one black bar labeled Unallocated. Right-click it and choose New Simple Volume. Accept the full size, pick a drive letter, choose NTFS as the file system, give it a label and leave Perform a quick format ticked. When the wizard finishes, the SSD appears in File Explorer.

Fix 3: Assign a drive letter

If the SSD already has a healthy partition but no letter, right-click the partition, choose Change Drive Letter and Paths, click Add and pick a letter. This is common with SSDs taken from another PC. For other reasons a partition can be hidden, see our guide to drives that appear in Disk Management but not File Explorer.

A cloned SSD can also show as Offline while the original drive is still connected, because both disks have the same disk ID. Right-click the disk label and choose Online, and Windows gives it a new ID.

Fixes when the SSD is not in Disk Management

Fix 4: Check whether the BIOS sees the SSD

Restart and enter your BIOS or UEFI setup, usually by pressing Delete, F2 or F10 during startup. Look on the storage, NVMe or boot pages for the SSD's model name. Many boards list NVMe drives on a separate page rather than with SATA devices.

If the BIOS does not list the SSD, Windows cannot see it either, and the cause is physical or a firmware setting. Our guide to a drive that is not showing in BIOS goes through those checks in detail.

Fix 5: Reseat the drive and check connections

  • M.2 SSDs: power off and unplug the PC. Remove the drive, check the slot for dust, insert it at an angle until the gold contacts are fully hidden, then press it down and fit the retaining screw or latch.
  • 2.5-inch SATA SSDs: check that both the SATA data cable and the SATA power cable are pushed fully home. Try a different SATA port and cable.

Fix 6: Check the M.2 slot type and lane sharing

M.2 is a connector shape, not a single standard. Some M.2 slots accept only NVMe drives, some only SATA, and some both. An M.2 SATA SSD in an NVMe-only slot will not be detected. Check your motherboard or laptop manual for what each slot supports.

Many desktop boards also share bandwidth between M.2 slots and SATA ports. Filling a certain M.2 slot can disable one or two SATA ports, or the other way round. The manual will have a table showing which combinations work.

Fix 7: Check the storage controller mode

On some laptops and desktops, especially those using Intel Rapid Storage Technology or Intel VMD, NVMe drives sit behind a RAID-style controller. Windows Setup then says it cannot find any drives until you load the storage driver from your PC maker. If you are installing Windows onto the new SSD, download the Intel RST or VMD driver for your model, put it on the USB installer, and click Load driver at the drive selection screen. Changing the controller mode to AHCI on a PC that already runs Windows can stop it booting, so only change it if you know what you are doing.

Fix 8: Update or reinstall storage drivers

  1. Press Win + X and open Device Manager.
  2. Expand Disk drives and Storage controllers, and look for warning icons.
  3. Right-click any device with a warning and choose Uninstall device, then click Action → Scan for hardware changes.
  4. Install the latest chipset and storage drivers from your motherboard or PC maker, and check for a BIOS update that mentions NVMe or storage compatibility.

Quick reference: symptoms and fixes

SymptomMost likely causeFix
Disk shows Not InitializedNew, empty SSDFix 1, then Fix 2
Disk shows UnallocatedNo volume createdFix 2
Healthy partition, not in File ExplorerNo drive letterFix 3
Not in Disk Management or BIOSSeating, cable or slotFixes 4 to 6
In BIOS, missing during Windows installRST or VMD driver neededFix 7
In BIOS, missing in WindowsDriver problemFix 8

Find the cause in one step

If you would rather not work through each check by hand, Disk Detector scans for every drive connected to your PC, including ones File Explorer will not show, and tells you exactly why a drive is missing: not initialized, no drive letter, offline, unallocated, unreadable file system, driver problem or not detected at all. For hardware problems it gives you step-by-step checks for cables, ports and settings.

Once the SSD is working, Disk Detector also reads its SMART health and wear level so you can confirm the new drive is healthy from day one, and run a speed benchmark to make sure it is running at the speed it should in the slot you chose.

Frequently asked questions

Why is my new SSD not showing in File Explorer?

A brand new SSD has no partition table, so Windows hides it from File Explorer until you initialize it and create a volume in Disk Management.

Should I choose GPT or MBR for a new SSD?

Choose GPT for almost every modern PC. MBR is only needed for very old BIOS-only systems and cannot use more than 2 TB of a disk.

Why does my M.2 SSD not show up in BIOS?

Common causes are a drive that is not fully seated, an M.2 slot that does not support the drive type (SATA or NVMe), or a slot that shares lanes with SATA ports and is disabled.

Get three guides like this every month, plus software update notices.Subscribe →