Disk Detector
Windows 10 & 11 Buy license · $29.95
Missing drives

Hard Drive or SSD Not Showing in BIOS: How to Get It Detected

Hard drive not showing in BIOS or UEFI? Check cables, power, SATA ports, M.2 slot sharing and firmware settings to get the drive detected again.

Updated 5 minute read The Disk Detector team

If a hard drive or SSD is not showing in BIOS, the computer's firmware cannot detect it, so Windows will not see it either and no Windows setting can fix it. The cause is almost always physical or a firmware setting: a loose or faulty SATA cable, a missing power connection, a SATA port that is disabled or shared with an M.2 slot, an M.2 drive in a slot that does not support its type, or a storage controller mode that hides the drive. Work through the checks below with the PC switched off and unplugged whenever you touch the hardware.

If the drive does appear in BIOS but not in Windows, the problem is different and usually easier. See our guides to an SSD not showing up in Windows and a drive that shows in Disk Management but not File Explorer.

Where to look in BIOS

Restart the PC and press the setup key during startup, usually Delete or F2 on desktops and F2, F10 or Esc on laptops. On Windows 11 you can also go to Settings → System → Recovery → Advanced startup → Restart now, then Troubleshoot → Advanced options → UEFI Firmware Settings.

Drives can be listed in several places, depending on the board:

  • The main or system information page
  • A storage, SATA configuration or onboard devices page
  • A separate NVMe configuration page. Many boards do not list NVMe drives with SATA drives.
  • The boot menu or boot priority list

Check all of them before deciding the drive is missing.

Step 1: Check power and cables

Power and spin-up

A hard drive should spin up with a hum and a slight vibration you can feel when the PC starts. If it is silent, it is not getting power or its electronics have failed. If it clicks or beeps, read our guide to hard drive clicking noises before going further.

For desktop SATA drives, check that the SATA power cable from the power supply is pushed fully in. Try a different power connector, ideally on a different cable from the power supply.

Some large hard drives removed from external enclosures will not spin up in certain desktops because the power supply sends voltage on a pin the drive uses as a "power disable" signal. A Molex-to-SATA power adapter usually solves it. If a drive from an external case is silent in your PC, this is a likely cause.

Data cables

  1. Reseat the SATA data cable at both ends. Latching cables should click.
  2. Try a different SATA cable. They fail more often than people expect, especially if they have been bent sharply.
  3. Plug into a different SATA port on the motherboard.
  4. For laptops, reseat the drive in its bay or connector.

Step 2: Check ports and M.2 slots

Disabled or shared SATA ports

Many motherboards share bandwidth between M.2 slots and SATA ports. Installing an M.2 drive in a particular slot can disable one or two SATA ports, and a hard drive plugged into one of those ports simply vanishes. Your motherboard manual has a table showing which ports are disabled by which slots. Move the SATA drive to a port that is not shared.

Some boards also let you enable or disable individual SATA ports, or set them to hot plug, in the SATA configuration page. Make sure the port your drive uses is enabled.

M.2 drives

  • Seating. Insert the drive at an angle until the gold contacts are fully hidden, then press it flat and fit the screw or latch. A half-seated drive is not detected.
  • Slot type. Some M.2 slots support only NVMe (PCIe), some only SATA, some both. An M.2 SATA drive in an NVMe-only slot will not show up, and the reverse is also true. Check the manual.
  • PCIe adapter cards. A card holding several NVMe drives in one PCIe slot needs the slot set to split its lanes (often called bifurcation) in BIOS, or only the first drive will appear.

Step 3: Check BIOS settings and firmware

Storage controller mode

The SATA or storage mode setting, usually AHCI or RAID, changes how drives appear. With RAID mode, or with Intel RST or VMD enabled, drives can be grouped behind a RAID controller and only show on that controller's own setup page. This is common on laptops, where NVMe drives are hidden from the normal list and from Windows Setup until the right driver is loaded.

Do not switch an existing Windows installation from RAID to AHCI, or the reverse, without preparing Windows first. It can stop the PC booting. If you are just checking for the drive, look on the RAID, RST or VMD page instead.

Firmware updates and compatibility

Older BIOS versions can lack support for newer NVMe drives or very large hard drives. Check your motherboard or PC maker's support page for a BIOS update that mentions storage compatibility. If you want the drive to appear as a boot option, make sure the PC is in UEFI mode rather than legacy or CSM mode, since NVMe boot support depends on it.

Step 4: Test the drive somewhere else

Connect the drive to another PC, or to the same PC through a USB-to-SATA adapter or NVMe enclosure. If it is detected that way, the drive is fine and the problem is your cable, port or board setting. If it is not detected anywhere, the drive has most likely failed.

Quick reference

SymptomLikely cause
Drive silent, no vibrationNo power, power-disable pin, or dead electronics
Disappears after adding an M.2 driveShared SATA port
M.2 drive not listed anywhereSeating or wrong slot type
Listed on RAID or VMD page onlyController mode
Works over USB but not inside the PCCable, port or board setting
Not detected on any PCFailed drive

Once the drive is back

When the drive shows in BIOS again, start Windows and make sure it appears and is healthy. Disk Detector picks up every connected drive, including ones that are not initialized, have no drive letter or are offline, and gives step-by-step checks for cables, ports and settings when a drive is not detected. It also reads the drive's SMART health, which matters here: a drive that vanished from BIOS once because of a fault may be close to failing for good. If Disk Detector rates it Caution or Bad, copy your files to another drive before trusting it again.

Frequently asked questions

Why is my NVMe SSD not listed with my SATA drives in BIOS?

Many UEFI setups list NVMe drives on a separate NVMe or storage page, not under SATA configuration. Check the boot menu too.

Can a SATA port be disabled in BIOS?

Yes. Some boards let you turn individual ports off, and some disable certain ports when an M.2 slot is in use.

If the drive is not in BIOS, can Windows fix it?

No. If the firmware cannot see the drive, Windows will not either. It is a hardware, connection or drive fault.

Get three guides like this every month, plus software update notices.Subscribe →