Disk Detector
Windows 10 & 11 Buy license · $29.95
USB and SD cards

USB Flash Drive Not Recognized in Windows 11 or 10? How to Fix It

USB flash drive not recognized by Windows? Check ports, drivers, drive letters and Disk Management, and learn when a stick is dead or can be saved.

Updated 5 minute read The Disk Detector team

When a USB flash drive is not recognized in Windows, start by plugging it into a different USB port, ideally one directly on the PC rather than a hub, and then open Disk Management to see whether Windows can see the stick at all. If it appears there, the fix is usually simple: a missing drive letter, an unreadable file system or a partition problem. If it does not appear anywhere, the cause is the port, the USB driver or a flash drive that has failed. The steps below take you through each case in order of how likely it is.

All the steps work on Windows 11 and Windows 10, and none of them erase your files unless clearly marked.

Step 1: Rule out the port and the PC

  1. Try a different port. Front-panel ports, keyboard ports and unpowered hubs are the most common cause of flaky USB sticks. On a desktop, use a port on the back.
  2. Remove extenders and adapters. Plug the stick straight into the PC. USB-C to USB-A adapters can be poor quality.
  3. Try a second computer. If the stick works there, it is healthy and the problem is with the first PC's settings or drivers.
  4. Do a full restart. Use Restart rather than Shut down. With Fast Startup turned on, Shut down does not fully reset hardware.

Many flash drives have a small LED. If it never lights, the stick is not getting power or its circuitry has failed.

Step 2: Check Disk Management

Press Win + X and choose Disk Management. Look for a disk marked Removable with a size close to your stick's capacity. A 64 GB stick shows as roughly 57 to 59 GB because Windows uses binary units.

What you seeMeaningWhat to do
Healthy partition, no letterWindows skipped the letterAssign a drive letter (Step 3)
RAWFile system damagedDo not format yet; copy data first
UnallocatedNo partitionCreate a volume only if the stick is empty
No MediaThe controller answers but no memory is foundUsually a failed stick
Wrong size, much smallerLeftover partitions from a boot driveClean and repartition if empty
Not listedDriver, port or hardware faultGo to Step 4

Step 3: Assign a drive letter

A stick that is healthy but has no drive letter will not appear in File Explorer. This often happens when Windows tries to reuse a letter already taken by a network drive or card reader.

  1. In Disk Management, right-click the stick's partition and choose Change Drive Letter and Paths.
  2. Click Add (or Change if it has a letter that clashes).
  3. Pick a letter later in the alphabet, such as U or W, and click OK.

More causes of hidden partitions are covered in our guide to drives that show in Disk Management but not in File Explorer.

Step 4: Check Device Manager

If the stick is not in Disk Management, open Device Manager from the Win + X menu.

  1. Expand Disk drives. If your stick is listed with a warning icon, right-click it and choose Uninstall device, unplug the stick, wait a few seconds and plug it back in.
  2. Expand Universal Serial Bus controllers. Look for Unknown USB Device (Device Descriptor Request Failed) or any entry with a yellow triangle. Uninstall it and reconnect the stick.
  3. If a USB Root Hub or host controller shows a problem, uninstall it too, then click Action → Scan for hardware changes. Your mouse and keyboard may pause briefly while Windows reinstalls the driver.

"Device Descriptor Request Failed" means Windows detected that something was connected but could not read its identity. A different port or cable often fixes it. If the error follows the stick to every port and every PC, the stick's controller has most likely failed.

Step 5: Turn off USB power saving

Windows can cut power to USB ports it thinks are idle, which can make sticks disconnect or fail to wake.

  1. Open Control Panel → Hardware and Sound → Power Options.
  2. Click Change plan settings next to your plan, then Change advanced power settings.
  3. Expand USB settings → USB selective suspend setting and set it to Disabled. Some newer laptops do not show this option.

You can also open each USB Root Hub in Device Manager, go to the Power Management tab and untick Allow the computer to turn off this device to save power.

Recognized but still not usable

Sometimes Windows detects the stick but you cannot use it properly. Three problems are common:

  • "The disk is write-protected." The stick may have a lock switch, a read-only flag, or a controller that has locked itself because the memory is worn out. See how to remove write protection from a USB drive.
  • "You need to format the disk." The file system is damaged or unreadable. Click Cancel and copy anything you can before formatting.
  • Files corrupt after copying. A cheap high-capacity stick that corrupts files once it fills up may be a fake that reports more space than it has. Our guide on how to check if a USB flash drive is fake shows how to test it.

Get a straight answer faster

Disk Detector checks removable drives the moment you plug them in. It tells you why a USB drive is not recognized, whether it is write-protected or failing, and whether its real capacity matches the label. If the stick needs a drive letter, that fix is one click.

Because the checks are read-only, Disk Detector will not change anything on the stick unless you choose a fix, and anything that could affect your data is clearly marked first. That makes it a safe first step when the stick holds files you need.

When the stick is beyond saving

If the stick is not detected on any port or any computer, or it shows No Media or 0 bytes everywhere, the controller or memory has failed. Software cannot fix that. If the files matter, a specialist recovery service can sometimes read the memory chips directly. If they do not, replace the stick, and keep a second copy of anything important on a different drive from now on. Flash drives are convenient, but they are not a safe place for the only copy of your files.

Frequently asked questions

Why does my USB stick work on one PC but not another?

The working PC proves the stick is fine, so the problem is on the other PC: a drive letter clash, a disabled USB controller, a driver issue or a power-saving setting on the port.

What does Unknown USB Device (Device Descriptor Request Failed) mean?

Windows saw something connect but could not read its identity. It is usually a bad port, cable or hub, or a flash drive controller that has failed.

Can I get files off a USB drive that is not recognized?

If it appears in Disk Management, often yes. If no PC detects it at all, the controller has usually failed and only a specialist recovery service can help.

Get three guides like this every month, plus software update notices.Subscribe →