A SMART hard disk error at startup means your drive has told the PC's firmware that it expects to fail. The message comes from the drive's own health monitoring, not from Windows, and it is almost always a real warning. You can usually press a key to continue and Windows will start, but treat the next hour as your best chance to save your files: back them up to another drive straight away, then replace the failing drive.
This guide explains what the different messages mean, how urgent they are and exactly what to do, in the order that gives you the best chance of keeping your data.
What the message looks like
The wording depends on your PC maker and motherboard, but they all mean the same thing. Common versions include:
- SMART Status Bad, Backup and Replace. Press F1 to Resume on many desktop motherboards.
- SMART Hard Disk Error 301 on many HP laptops and desktops, often with a note that the hard disk check has detected an imminent failure.
- Hard drive SMART predictive failure or similar wording on other brands.
- A notification inside Windows saying a drive may be failing or is at risk.
SMART (Self-Monitoring, Analysis and Reporting Technology) is built into every modern hard drive and SSD. The drive tracks readings such as bad sectors, read errors and spin-up problems, and compares each against a failure threshold set by the manufacturer. When one crosses its threshold, the drive changes its overall status to "failing", and the firmware shows the warning during startup.
How urgent is it?
Very. Manufacturers set SMART thresholds conservatively, so by the time a drive reports a failing status, the problem has usually been building for a while. Some drives keep running for months after the warning; others fail within days. There is no way to know which yours will be, so assume it is the short end.
Do not disable SMART in the BIOS to make the message go away. That hides the warning without changing anything about the drive.
Step 1: Back up your files now
Press the key the message asks for (usually F1 or Enter) to continue to Windows. Then, before you do anything else:
- Plug in an external drive or USB stick with enough space.
- Copy your most important files first: documents, photos, anything you cannot replace. Your user folders are under
C:\Users\YourName. - Then copy the next most important things, such as browser bookmarks, email files and saved passwords exported from your password manager.
- Check a few of the copied files open properly on the backup drive.
Copy in small batches rather than the whole drive at once. If the drive has bad areas, a single large copy can stall on one unreadable file. If something will not copy, skip it and move on. Our guide on how to back up a failing hard drive covers this in more detail, including cloning and what to do if Windows will not start.
While you are backing up, do not run defragmentation, chkdsk /r, disk cleanup or large updates. They all put extra strain on a drive that is already struggling.
Step 2: Find out what triggered the warning
Once your files are safe, it helps to know which reading tripped the alarm. It confirms the warning is genuine and gives you evidence for a warranty claim.
Windows itself only tells you the overall status. In Terminal, the command Get-PhysicalDisk | Select FriendlyName, HealthStatus shows Healthy, Warning or Unhealthy for each drive, but not why. To see the individual readings, you need a SMART tool. Disk Detector reads the full SMART data for hard drives, SSDs and NVMe drives, rates each drive Good, Caution or Bad and explains the exact reasons, such as a rising reallocated sector count, in plain English. You can also save or print a full report of the drive, with its model and serial number, for a warranty claim.
| Common trigger | What it means |
|---|---|
| Reallocated Sectors Count (5) | The drive has run through too many spare sectors |
| Current Pending Sector Count (197) | Sectors the drive cannot read; some data may already be lost |
| Spin Retry Count (10) | The motor is struggling to spin the disk up |
| Reported Uncorrectable Errors (187) | Reads failing even after error correction |
| SSD available spare or percentage used | Flash memory is worn out or running short of spare blocks |
For the full list, see SMART attributes explained.
Can it be a false alarm?
Rarely. A handful of drive models have had firmware bugs that misreported values, and that is usually documented by the manufacturer with a firmware update. In nearly every case, a failing SMART status reflects a real hardware problem. If your SMART readings look normal but the BIOS still reports a failure, check the manufacturer's support site for a firmware update and run their diagnostic, but keep your backup current in the meantime.
The one thing a SMART warning cannot be is fixed by software. Formatting, reinstalling Windows or running repair tools does not reset the drive's health readings. Bad sectors are worked around, not repaired.
Step 3: Replace the drive
With your files safe, plan the replacement. You have two choices:
- Clean install: fit the new drive, install Windows fresh from a USB installer, then copy your files back. This is the most reliable option and avoids carrying any problems over.
- Clone: copy the whole old drive to the new one with cloning software. It saves reinstalling programs, but the clone may fail or copy damaged files if the old drive has many bad sectors. Clone soon, before the drive gets worse.
If you are replacing a hard drive in a laptop or older desktop, it is a good moment to move to an SSD, which will make the PC feel much faster. Check whether your PC takes a 2.5-inch SATA drive or an M.2 drive before you buy.
Check the warranty first. Many drives carry a warranty of two to five years, and a failing SMART status is generally accepted as a fault. Look up the serial number on the manufacturer's website. If the drive holds personal data, think about whether you want to send it away, since a failing drive may not be possible to wipe completely.
What if the PC will not start after the message?
If pressing the key does not get you into Windows, or Windows freezes or restarts during startup, the drive may be too damaged to boot from. Do not keep power cycling it. Instead:
- Remove the drive and connect it to another PC with a USB adapter or dock, as a second drive.
- Copy your files from it there, starting with the most important.
- If it clicks, beeps or is not detected at all, stop and consider a professional recovery service for anything irreplaceable.
Our guide to the signs a hard drive is failing explains the warning signs that usually come before and after a SMART error.
Avoid being caught out next time
A startup message is the last line of warning, and some drives never show one before they fail. Two habits protect you better:
- Keep an automatic backup running so a sudden failure costs you hours, not years of files.
- Watch drive health in the background. Disk Detector can check your drives on a schedule and show a desktop alert when a reading starts to change, usually well before the drive's own threshold is reached.
Frequently asked questions
Can I ignore a SMART hard disk error and keep using the PC?
You can press the key to continue, but treat it as an urgent warning. Back up immediately.
Can a SMART error be a false alarm?
Rarely. Firmware bugs exist, but most warnings reflect a real problem such as reallocated sectors.
Will replacing the drive remove the SMART error?
Yes. The message comes from the drive itself, so a new healthy drive will not show it.
