To check SSD health on Windows, read three things from the drive's SMART data: how much of its rated life has been used (wear level), how many spare memory blocks are left, and whether it has logged any media errors. On Windows 10 and 11 you can see the first two for NVMe SSDs in Settings → System → Storage → Advanced storage settings → Disks & volumes → Properties. SATA SSDs do not appear there, so you need PowerShell or a SMART tool. This guide shows each method and explains what the numbers mean.
SSDs fail differently from hard drives. They do not click or slow down gradually from a damaged surface. Instead, their flash memory wears out with every write, and the drive tracks that wear precisely. That makes SSD health easier to predict, as long as you know where to look.
What "SSD health" actually measures
Flash memory cells can only be erased and rewritten a limited number of times before they stop holding data reliably. To spread that wear evenly, the SSD's controller constantly moves data around (wear leveling) and keeps a pool of spare blocks to swap in when cells wear out. It also counts every write. That bookkeeping is what the health values below report, which is why an SSD can often tell you, months in advance, that it is nearing the end of its rated life.
| Measure | What it means | Healthy | Worry when |
|---|---|---|---|
| Percentage used / wear | Share of rated write endurance used | Low and rising slowly | Approaching 100 percent |
| Available spare | Reserve blocks left to replace worn ones | At or near 100 percent | Falling toward its threshold |
| Media and data integrity errors | Reads or writes the drive could not complete | 0 | Any count above zero |
| Critical warning | NVMe flag for spare, heat or read-only state | 0 | Anything else |
| Data written | Total host writes over the drive's life | Well under the rated TBW | Near or past the rated TBW |
| Temperature | Current drive temperature | Moderate in normal use | Often hot enough to throttle |
| Unsafe shutdowns | Power lost without a clean shutdown | Low | Climbing quickly |
NVMe drives report these in a standard health log, so the names are the same on every brand. SATA SSDs use numbered SMART attributes, and the names vary by maker, for example "Wear Leveling Count", "SSD Life Left" or "Media Wearout Indicator". They measure the same thing. Our reference to SMART attributes explained lists the common ones.
Method 1: Windows Settings (NVMe only)
- Open Settings → System → Storage.
- Click Advanced storage settings, then Disks & volumes. In Windows 10, choose Manage Disks and Volumes.
- Select your NVMe SSD and click Properties.
- Read the Drive health section.
Estimated remaining life is simply 100 minus the drive's percentage used. Available spare and Temperature are shown too. If the drive is in trouble, Windows adds a warning in this panel. If you see no Drive health section at all, the drive is a SATA SSD or a hard drive.
Method 2: PowerShell (SATA and NVMe)
Right-click Start, choose Terminal (Admin), and run:
Get-PhysicalDisk | Get-StorageReliabilityCounter | Select-Object DeviceId, Wear, Temperature, TemperatureMax, ReadErrorsUncorrected, WriteErrorsUncorrected, PowerOnHours
Wear is the percentage of rated life used. DeviceId matches the disk number in Disk Management. Run Get-PhysicalDisk on its own to match numbers to model names and see each drive's HealthStatus.
Expect some blank values. What Windows can read depends on the drive and its driver, and some SATA SSDs report little through this command.
SSD makers also offer their own utilities that read SMART data for their drives. They are useful for firmware updates, but each one only covers its own brand.
Method 3: Compare data written with the TBW rating
Every SSD has an endurance rating in terabytes written (TBW), printed on its datasheet. As a rough guide, many 1 TB consumer drives are rated somewhere around 600 TBW, though it varies a lot by model. Compare that with the total data written in your drive's SMART data. If you have written 60 TB to a 600 TBW drive, you have used about 10 percent of its rated endurance.
TBW is a warranty figure, not a cliff edge. Many drives keep working well past it. But a drive near its rating is closer to the end of its reliable life, and you should plan for that. For more on how long drives typically last, see how long SSDs last.
Signs an SSD needs attention
- Media errors above zero, even if everything else looks fine.
- Available spare dropping noticeably between checks.
- The drive switching to read-only. Many SSDs do this deliberately when worn out, so you can still copy your data off.
- Frequent overheating. NVMe drives throttle when hot, which slows them down. Our guide to normal drive temperatures lists safe ranges.
- Crashes or freezes during large writes or file copies.
See SSD health in plain English
Disk Detector reads SMART data from SATA SSDs and NVMe drives (and hard drives too) and gives each one a Good, Caution or Bad rating with the reasons spelled out. For SSDs it shows how much of the rated life has been used and estimates how long the drive has left at your current usage, along with its temperature.
With background checks turned on, Disk Detector sends a desktop alert if an SSD starts showing warning signs or gets too hot, so you find out while there is still plenty of time to back up. You can also save a full health report as PDF or text, which is handy if you need to make a warranty claim.
What to do with the results
- Under 50 percent used, no errors: nothing to do. Check again every few months.
- 50 to 90 percent used, no errors: normal for an older drive. Keep backups current and check monthly.
- Over 90 percent used, or spare falling: plan a replacement and make sure everything on it is backed up.
- Any media errors, critical warnings or read-only mode: copy your data off now and replace the drive.
Whatever the numbers say, an SSD is not a backup. Even a healthy one can fail suddenly from a controller or power fault, so keep a second copy of anything you would hate to lose. For checking every drive in your PC at once, including hard drives, see our guide on how to check hard drive health in Windows 11.
Frequently asked questions
What is a good SSD health percentage?
Anything above about 90 percent life left is normal for a drive a few years old. Below 10 percent, plan a replacement and keep backups current.
Does Windows show SSD health?
Windows 10 and 11 show estimated remaining life and temperature for NVMe SSDs in Settings. SATA SSDs need PowerShell or a SMART tool.
Does an SSD stop working when it reaches 100 percent used?
Not immediately. The rating is a warranty estimate, and many drives keep working well past it, but the risk of failure rises so you should replace it.
