To monitor hard drive health on Windows, you need something that reads each drive's SMART data on a schedule and warns you when a value changes, not just when the drive finally declares itself failing. Windows has limited built-in monitoring: it can warn about some NVMe SSDs and shows an overall health status in PowerShell, but it does not watch the readings that give early warning, such as reallocated sectors or temperature. The reliable approach is a background tool that checks daily, alerts you on change, and a backup that is always running in case it does.
This guide explains what to monitor, what Windows can and cannot do on its own, and how to set up automatic checks that catch problems while there is still time to save your files.
Why monitoring beats checking once
A one-time health check tells you how a drive is today. Most drive failures are not sudden: sector counts creep up, read errors increase, temperatures rise. The useful signal is the change. A drive with 4 reallocated sectors that has been stable for two years is in a very different state from one that had 0 last week. Only regular checks show you that difference.
The other reason is simple: nobody remembers to check. Automatic monitoring turns drive health into something you only think about when there is something to do.
What to monitor
| Reading | Applies to | Why it matters |
|---|---|---|
| Reallocated Sectors Count (5) | Hard drives | A rising count means the surface is wearing |
| Current Pending Sector Count (197) | Hard drives | Unreadable sectors right now; act immediately |
| Reported and offline uncorrectable errors | Hard drives | Reads failing even after error correction |
| Percentage used / life left | SSDs and NVMe | How much of the rated write endurance is used |
| Available spare and media errors | SSDs and NVMe | Falling spare or any media errors mean trouble |
| Temperature | All drives | Heat shortens hard drive life and throttles SSDs |
| Free space | All drives | A full drive slows Windows and can stop updates |
For what normal values look like, see SMART attributes explained and normal hard drive temperature.
What Windows does on its own
Storage health notifications
Windows 11 can show a notification when an NVMe SSD reports a serious problem, such as running low on spare blocks or entering read-only mode. It does not do this for most SATA hard drives and SSDs, and it fires only when the drive reports a critical state, which is late in the process.
Drive health in Settings
For NVMe drives, Settings → System → Storage → Advanced storage settings → Disks & volumes → Properties shows estimated remaining life, available spare and temperature. It is a manual snapshot, not monitoring.
PowerShell health status
In Terminal, Get-PhysicalDisk | Select FriendlyName, MediaType, HealthStatus lists each drive as Healthy, Warning or Unhealthy. This reflects the drive's overall SMART pass or fail, which only flips when a value crosses the manufacturer's threshold. Many drives show Healthy right up to the point of failure.
You can schedule that command with Task Scheduler and have it write to a log, but you would still need to read the log, and it still only reports the final pass or fail. Our guide to checking hard drive health in Windows 11 covers these built-in tools in more detail.
Set up automatic monitoring
Disk Detector can run quietly in the background and check your drives on a schedule. It reads SMART for hard drives, SSDs and NVMe drives, watches temperatures and free space, and shows a desktop notification if a drive starts showing warning signs, gets too hot or runs low on space. Each alert comes with the reason in plain English and what to do about it.
- Install Disk Detector and open it. Every connected drive is found automatically.
- Check the current rating for each drive. Deal with anything rated Caution or Bad before relying on monitoring.
- Turn on background checks and choose a schedule. Daily checks are light and catch changes early.
- Save or print a health report now, so you have a baseline to compare against later.
Reading SMART data takes a moment and uses almost no resources, so daily checks will not slow the PC down.
How often to check
- SMART readings and temperature: daily, in the background.
- Free space: continuously, with an alert well before the drive is full. Try to keep at least 10 percent of each drive free.
- Full surface scan: every few months on hard drives that hold important data, and any time SMART readings change. A surface scan reads the whole drive and takes hours, so it is not something to run daily.
- External and backup drives: check whenever you connect them. A backup drive that sits in a drawer can fail unnoticed.
What to do when you get an alert
| Alert | First action |
|---|---|
| New reallocated or pending sectors | Make sure your backup is current today. Recheck within a week. |
| Drive rated Bad | Copy your files off now and plan a replacement. |
| Temperature too high | Check fans, vents and airflow. Clean dust. |
| SSD life running low | Plan a replacement before it reaches its rated limit. |
| Low free space | Clear temporary files and move large files elsewhere. |
For a drive that is actually failing, our guide on how to back up a failing hard drive explains how to copy your files without making things worse.
Warning signs to watch for yourself
Some problems show up in how the PC behaves before they show up in any reading. Pay attention if you notice any of these, and run a manual health check when you do:
- Clicking, grinding or repeated spin-up sounds from a hard drive.
- Files that take much longer to open than they used to, or copies that stall partway.
- Freezes of several seconds when opening folders, with the disk light on solid.
- Files or folders that suddenly become unreadable or corrupted.
- Disk errors in Event Viewer under Windows Logs → System, such as event ID 7 or 153 from the disk source.
Any of these, combined with a change in SMART readings, is a strong sign the drive needs replacing soon.
Monitoring is not a backup
Health monitoring gives you warning, but not every failure gives warning. Electronics can fail suddenly, laptops get dropped, and drives get stolen. Keep an automatic backup of anything you cannot replace, ideally with one copy on a separate drive and one somewhere other than your home. Monitoring then becomes the thing that tells you when to swap a drive on your own schedule, rather than in the middle of a crisis.
Frequently asked questions
Does Windows warn you when a drive is failing?
Sometimes. Windows can show a notification when a drive reports a SMART failure, but it often comes late or not at all.
How often should drive checks run?
Daily background checks are light and catch changes early. A full surface scan once every few months is plenty.
Does monitoring slow the PC down?
No. Reading SMART data takes a moment and uses almost no resources.
