To check a used hard drive or SSD, read its SMART health data, run a full surface scan and test its speed before you put anything important on it. On a hard drive, the numbers that matter most are reallocated, pending and uncorrectable sectors, which should all be zero, plus power-on hours to judge its age. On an SSD, look at percentage used (or life left), total data written, available spare and media errors. A used drive that passes all of these can be perfectly usable, but treat it as a drive with less life left than a new one, and keep your backups current.
This guide walks through each check, what a good and bad result looks like, and how to spot a used drive being sold as new.
Before you start
- Connect it directly if you can. A SATA port inside a desktop gives you the most reliable readings. Many USB enclosures and docks do not pass SMART data through to Windows, so you may see nothing at all over USB.
- Do not copy your files to it yet. Run the checks first, while the drive holds nothing you would miss.
- If buying in person, ask to see the drive running and its health readings before you pay. A seller with a healthy drive has no reason to refuse.
Step 1: Read the SMART data
Every modern drive keeps a health log called SMART. Windows does not show it in detail, so you need a tool that reads the full set of values. Disk Detector reads SMART for hard drives, SSDs and NVMe drives, rates the drive Good, Caution or Bad, and explains each reason in plain English. Note the readings down, or save a report, so you can compare them later.
Hard drive readings
| Reading | Good result | Warning sign |
|---|---|---|
| Reallocated Sectors Count (5) | 0 | Any value, especially if it changes during your checks |
| Current Pending Sector Count (197) | 0 | Any value: unreadable sectors right now |
| Offline Uncorrectable (198) | 0 | Any value |
| Reported Uncorrectable Errors (187) | 0 | Any value |
| Spin Retry Count (10) | 0 | Any value: motor or power problems |
| UDMA CRC Error Count (199) | 0 or low | A high count usually means a bad cable or connection, not a bad disk |
| Power-On Hours (9) | Matches the seller's story | Tens of thousands of hours on a drive described as lightly used |
Power-on hours tell you age, not health. A drive with 30,000 hours and zero sector problems may outlast one with 3,000 hours and a handful of reallocated sectors. Still, a drive that has run for years is further along its life, and the price should reflect that. Our guide to reallocated sectors count explains why that attribute matters so much.
SSD readings
| Reading | What to look for |
|---|---|
| Percentage used / life remaining | How much of the rated life is used. Lower used is better. |
| Data written (total host writes) | Compare with the drive's rated endurance (TBW) from the maker's spec sheet |
| Available spare | Should be at or near 100 percent |
| Media and data integrity errors | Should be 0 |
| Unsafe shutdowns | A high number is common and not alarming on its own |
Disk Detector shows how much of an SSD's rated life has been used, with an estimate of how long it has left at your current usage. Our guide on how long SSDs last puts these numbers in context.
Step 2: Run a full surface scan
SMART only knows about problems the drive has already found. A drive that has sat unused for months may have weak areas it has not discovered yet. A full read scan visits every block and reports any that are bad or unusually slow.
- Start a read-only surface scan of the whole drive. On a large hard drive this takes several hours, roughly 1.5 to 3 hours per terabyte.
- Watch for bad blocks and clusters of slow blocks.
- When it finishes, read the SMART values again and compare them with Step 1.
Disk Detector's surface scan is read-only and shows a live map as it goes. A clean scan with unchanged SMART values is a good sign. Any new reallocated or pending sectors during the scan mean the drive is deteriorating under load: return it if you can. See how to check a hard drive for bad sectors for how to read the results.
Step 3: Test the speed
A speed test confirms the drive performs as it should. Compare read and write speeds with what that model is rated for. A hard drive that reads far below its rating, or slows dramatically in some areas, may have a worn surface. An SSD that is much slower than expected may be heavily worn or have firmware problems. Use the same port and cable you plan to use, since a slow port can make a good drive look bad.
Step 4: Check the warranty and history
- Look up the serial number on the manufacturer's website. It shows whether the drive is still under warranty and sometimes which region it was sold in.
- Be wary of "new" drives with odd details: a missing or expired warranty on a drive sold as new, mismatched labels, or scuffed screw holes. SMART hours can be reset with specialist tools, so low hours on their own do not prove a drive is new.
- Check the capacity on cheap drives from marketplaces. A fake-capacity test writes data across the whole drive and reads it back, which exposes drives that report more space than they have.
Step 5: Wipe it and start clean
Once a drive passes, remove whatever the previous owner left behind:
- Open Disk Management, delete any existing partitions on the used drive (double-check you have the right disk), then create a new simple volume.
- Format it with Quick Format unticked. On Windows, a full format writes zeros to the whole volume and checks every sector, which doubles as a final write test.
Do not open files left on the drive by a previous owner. Apart from privacy, you do not know where they came from.
Decide what to trust it with
- All checks clean, moderate hours: fine for everyday use, games or as a backup target alongside another copy.
- Clean but very high hours or heavy SSD wear: fine for scratch space or replaceable data, not your only copy of anything.
- Any sector problems, scan errors or growing counts: do not use it for anything you care about. Return it if you can.
Whatever you decide, keep checking. A used drive's history is partly unknown, so watching for change matters more than on a new one. Disk Detector can check drives on a schedule in the background and warn you with a desktop alert if a reading starts to move.
Frequently asked questions
How many power-on hours is too many for a used hard drive?
There is no fixed limit, but drives with tens of thousands of hours are well into their life. Health values matter more than age.
What should I check first on a used SSD?
Percentage used or life left, total data written, and media errors.
Should I wipe a used drive before using it?
Yes. Reformat it so you start clean.
