Most SSDs last 5 to 10 years or more in a typical home PC, and for most people the drive is replaced for being too small or too slow long before its flash memory wears out. An SSD's endurance is rated in TBW (terabytes written): a typical 1 TB consumer drive is rated for several hundred terabytes, while a home user writes perhaps 5 to 15 TB a year. You can see how much of your own SSD's rated life has been used in its SMART data, and that number is a far better guide than the drive's age.
This guide explains what wears an SSD out, how to read its endurance rating, how to estimate your drive's remaining life on Windows, and the signs that it is nearing the end.
Why SSDs wear out
An SSD stores data in NAND flash cells. Each time a cell is erased and rewritten, its insulating layer wears a little. After enough of these program/erase (P/E) cycles, the cell can no longer hold a charge reliably. Reading data does not wear flash in the same way; it is writing that counts.
The drive's controller spreads writes evenly across all cells (wear leveling) and keeps spare blocks in reserve to replace worn ones. When spares run low, the drive is near the end of its rated life. Many SSDs switch to read-only mode at that point, so you can still copy your data off.
How many cycles a cell can take depends on how many bits it stores:
| Flash type | Bits per cell | Relative endurance | Where you find it |
|---|---|---|---|
| SLC | 1 | Highest | Industrial drives, and as a fast cache area on consumer drives |
| MLC | 2 | High | Older and some high-end drives |
| TLC | 3 | Good | Most mainstream consumer SSDs today |
| QLC | 4 | Lower | Budget and high-capacity drives |
TBW, DWPD and warranty
Manufacturers express endurance in one of two ways:
- TBW (terabytes written): the total amount of data you can write during the warranty. Larger drives get higher ratings because they have more cells to spread writes over. A 2 TB model is usually rated for about twice the TBW of the 1 TB version.
- DWPD (drive writes per day): how many times you can fill the whole drive every day for the warranty period. This is more common on business and data center drives.
The warranty, often 3 or 5 years for consumer drives, ends at whichever comes first: the time limit or the TBW figure. Your drive's exact rating is on its datasheet or the maker's product page.
TBW is a warranty figure, not a cliff edge. Drives commonly keep working well past it, but you should not count on that.
A quick lifespan estimate
You can estimate how long your drive's endurance lasts with simple arithmetic:
- Find the drive's TBW rating, for example 600 TBW.
- Find how much you write per year. Check the drive's total data written (see the next section) and divide by the years you have owned it.
- Divide the TBW by your yearly writes.
A drive rated for 600 TBW that sees 10 TB of writes a year would take 60 years to reach its rating. Even heavy users who write 50 TB a year would take 12 years. In practice, other things usually end an SSD's life first: controller or firmware faults, power problems or physical damage. That is why endurance alone does not guarantee a long life, and why backups matter for any drive.
Workloads that do write heavily include video editing scratch disks, virtual machines, large game libraries that are reinstalled often, and download or torrent folders. If that is you, keep an eye on the wear figure.
How to check your SSD's remaining life on Windows
Settings (NVMe drives)
- Open Settings → System → Storage → Advanced storage settings → Disks & volumes.
- Select the NVMe drive and click Properties.
- Under Drive health, read Estimated remaining life and Available spare.
PowerShell (SATA and NVMe)
Right-click Start, choose Terminal (Admin) and run:
Get-PhysicalDisk | Get-StorageReliabilityCounter | Select-Object DeviceId, Wear, PowerOnHours
Wear is the percentage of rated life used. Some drives leave it blank. Our full guide on how to check SSD health covers these methods and the other values in detail.
What the SMART fields mean
NVMe drives report Percentage Used (which can go past 100), Available Spare and Data Units Written. SATA SSDs use maker-specific attributes with names such as Wear Leveling Count or SSD Life Left, plus Total LBAs Written. See SMART attributes explained for how to read them.
Disk Detector reads these values for you and shows how much of an SSD's rated life has been used, along with an estimate of how long it has left at your current usage. That turns a raw counter into a number you can plan around.
Signs an SSD is nearing the end
- Wear or percentage used near 100, or available spare falling toward its threshold.
- Media and data integrity errors above zero on an NVMe drive.
- Files that fail to open or copy, with Windows reporting they are corrupted or unreadable.
- The drive becoming read-only. You can open files but not save or delete anything.
- Sudden freezes or blue screens while the PC is reading from the drive.
- The drive disappearing from Windows or the BIOS. Unlike hard drives, SSDs often fail suddenly rather than gradually.
Our guide to the signs a drive is failing covers both hard drives and SSDs.
Unpowered SSDs and data retention
Flash cells slowly leak charge when the drive has no power. A new drive keeps data unpowered for a long time, but retention drops as the cells wear, and heat speeds the leak up. Industry endurance standards for client drives only require data to survive about a year unpowered at room temperature once a drive has used up its rated endurance.
The practical rule: do not use an SSD sitting in a drawer as your only long-term archive. Keep a second copy elsewhere, and power up and check stored drives now and then.
How to make an SSD last longer
- Keep free space. Leaving 10 to 20 percent of the drive empty gives wear leveling room to work and keeps the drive fast.
- Leave TRIM on. Windows enables it by default and runs it through Optimize Drives. Do not run old-style defragmenters on an SSD.
- Keep it cool. Heat does not use up write endurance, but sustained high temperatures are not good for the controller or data retention.
- Avoid power cuts. Shut down properly. Repeated unsafe shutdowns are a common cause of SSD corruption.
- Do not obsess over writes. Moving your browser cache or turning off the page file is rarely worth it on a modern drive.
The best protection is the same as for any drive: check its health every so often, and keep a backup. Disk Detector can check your drives on a schedule in the background and alert you if an SSD starts showing warning signs, so you can replace it on your terms.
Frequently asked questions
What does TBW mean on an SSD?
Terabytes Written is the amount of data the maker rates the drive to handle under warranty. Most home users write far less than that.
Do SSDs last longer than hard drives?
They have no moving parts, so they handle knocks better, but both wear out. Back up either type.
Does leaving an SSD unpowered lose data?
Over long periods it can, especially for worn drives kept warm. Do not use an unpowered SSD as your only long-term archive.
