An SSD running slow is usually caused by one of a few things: the drive is nearly full, TRIM is not running, it is connected to a slower port or slot than it supports, it is overheating and throttling, or the storage controller is in the wrong mode. Less often, the drive is wearing out or its firmware needs an update. Start by measuring its real speed, then work through the nine fixes below. Most take a few minutes and none of them put your data at risk if you follow the notes.
First, measure the speed
"Slow" can mean slow boots, slow file copies or a PC that freezes for seconds at a time, and each points somewhere different. A benchmark gives you a number to compare against what the drive should manage.
Windows has a basic built-in test. Open Terminal (Admin) and run winsat disk -drive c, replacing c with the drive letter. It reports sequential and random read and write speeds in MB/s. Compare the sequential read figure with the speed on the box: a SATA SSD should read at roughly 500 MB/s, and an NVMe drive should be several times faster.
Disk Detector includes a speed benchmark that measures read and write speeds and compares them with what the drive should manage, which makes a slow port, cable or failing drive easy to spot. Our guide on how to test hard drive speed on Windows explains how to read the results.
| Symptom | Most likely cause |
|---|---|
| Fast at first, then slows sharply during big copies | Cache running out, or overheating |
| Slow all the time, about 250 MB/s or less on a SATA SSD | Wrong port, controller mode or cable |
| Got slower over months, drive nearly full | Low free space, TRIM not running |
| Freezes and stalls, 100% disk in Task Manager | Background activity or a failing drive |
1. Free up space
SSDs need empty space to work efficiently. When a drive is nearly full, it has fewer free blocks for incoming writes and has to do more housekeeping first, and on many drives the fast cache area also shrinks. Keep at least 10 to 20 percent of the drive free. Our guide to freeing up disk space in Windows 11 lists safe ways to do it.
2. Make sure TRIM is on
TRIM tells the SSD which blocks are no longer in use, so it can prepare them for new data. Without it, write speed degrades over time.
- Open Terminal (Admin).
- Run
fsutil behavior query DisableDeleteNotify. - If the result for NTFS says
DisableDeleteNotify = 0, TRIM is enabled. If it says 1, runfsutil behavior set DisableDeleteNotify 0.
3. Let Windows optimize the drive
Click Start, type Defragment and Optimize Drives and open it. Your SSD should be listed with media type Solid state drive. Click Optimize: for an SSD, Windows sends TRIM commands for the whole drive instead of defragmenting it. Make sure Scheduled optimization is turned on. Do not use third-party defragmenters on an SSD; they add wear and do not help.
4. Check the port, slot or cable
An SSD can only run as fast as its connection.
- SATA SSD: connect it to a SATA III (6 Gb/s) port. Older or secondary controllers on some motherboards are 3 Gb/s and cap the drive at about half speed. Try a different SATA cable too.
- NVMe SSD: check your motherboard manual. Some M.2 slots run at a lower PCIe generation or with fewer lanes, and some share bandwidth with other slots. A PCIe 4.0 drive in a PCIe 3.0 slot works, but at PCIe 3.0 speeds.
- External SSD: use a USB 3.x or USB-C port and the cable that came with the drive. On a USB 2.0 port, any SSD drops to around 40 MB/s.
5. Check the controller mode in BIOS
SATA SSDs should run in AHCI mode. If the BIOS is set to IDE or legacy mode, the drive loses features and speed. You can check in Device Manager: under IDE ATA/ATAPI controllers, an entry with "AHCI" in its name means AHCI is in use.
Do not change the controller mode in BIOS on the drive Windows boots from without preparing Windows first. Switching modes without that preparation can stop Windows from starting. Look up the safe-mode method for your Windows version, and have a backup before you try it.
6. Watch the temperature
NVMe drives slow themselves down when they get too hot, which shows up as a sudden drop in speed partway through a long copy. M.2 drives tucked under a graphics card or in a laptop with poor airflow are the usual victims. Check the drive's temperature during a large transfer. If it climbs into the 70s Celsius and speed falls at the same time, you have found the problem. See our guide to NVMe SSD overheating for cooling fixes.
7. Understand the cache
Many consumer SSDs, especially lower-cost and QLC models, write to a fast cache first and move data to slower flash later. During a very large copy, once the cache fills, write speed can fall a long way, sometimes below a hard drive. That is normal behavior for those drives, not a fault. If you regularly copy very large files, a drive with a larger cache or TLC flash will hold its speed better.
8. Update firmware and check the power plan
Drive makers release firmware updates that fix performance and reliability problems. Download your SSD maker's utility from their official site to check. Back up first: firmware updates are usually safe, but a power loss partway through can make a drive unusable.
On desktops, aggressive power saving can add delays. In Control Panel → Power Options, try the Balanced or High performance plan and see if the stalls go away.
9. Check the drive's health
An SSD that has slowed down for no obvious reason may be wearing out or developing errors. Look at its health readings: percentage of life used, available spare and media errors. How to check SSD health on Windows explains the numbers. Disk Detector reads these for SATA and NVMe drives and rates the drive Good, Caution or Bad in plain English. If the health is poor, back up before you do anything else and plan a replacement.
Is it the drive or the PC?
If the benchmark is fast but the PC still feels slow, the drive is probably fine and the cause is elsewhere: too little memory, a busy antivirus scan, startup programs or Windows Update running in the background. Open Task Manager and sort by the Disk column to see which process is keeping the drive busy. A healthy SSD that benchmarks well is rarely the bottleneck.
Frequently asked questions
Does a full SSD slow down?
Yes. Most SSDs slow noticeably once they are nearly full. Keep at least 10 to 20 percent free.
Should I defragment an SSD?
No. Leave Windows Optimize Drives on its schedule, which sends TRIM commands to SSDs, and do not run third-party defragmenters on them.
Can heat slow an SSD down?
Yes. NVMe drives throttle when hot, and speed drops sharply during long transfers.
