A RAW drive is one where Windows cannot recognize the file system, so it cannot show you any files. The fix without formatting is to work out why it is RAW first: rule out the cable, port and enclosure, check the drive's health, check whether it uses a file system Windows cannot read, and only then repair or rebuild the volume. If the file system is genuinely damaged, the safe order is to recover your files to another drive first and format afterward. Whatever you do, do not click Format disk when Windows offers it.
This guide explains how to identify a RAW drive, the common causes, and the steps to fix it in the order that best protects your data.
How to tell if a drive is RAW
You will usually see one or more of these:
- A pop-up saying "You need to format the disk in drive E: before you can use it."
- An error such as "E:\ is not accessible. The volume does not contain a recognized file system."
- In Disk Management (Win + X → Disk Management), the partition shows RAW where it would normally say NTFS, exFAT or FAT32.
- The drive's properties show 0 bytes used and free.
- chkdsk replies: "The type of the file system is RAW. CHKDSK is not available for RAW drives."
The format prompt has its own set of causes beyond RAW, covered in our guide to the "you need to format the disk" error.
Why drives turn RAW
| Cause | Typical situation | Files recoverable? |
|---|---|---|
| Unsafe removal or power loss | USB drive unplugged mid-copy, power cut | Usually yes |
| Damaged boot sector or partition table | Malware, a bad disk tool, a failed resize | Usually yes |
| Faulty connection or enclosure | Worn cable, failing USB bridge board | Yes, once connected properly |
| Unsupported file system | Drive from a Mac, Linux PC, camera or TV recorder | Yes, on the original device |
| Third-party encryption | Drive encrypted with software not on this PC | Yes, with the right software and key |
| Failing drive | Bad sectors where the file system's key structures live | Often, but time matters |
Step 1: Click Cancel and stop writing to the drive
If Windows asks to format the drive, click Cancel. Do not save anything to the drive, do not initialize it, and do not run tools that "fix" it by writing a new file system. Every write risks overwriting the data you want back.
Then rule out the connection
- Safely disconnect the drive and connect it to a different USB port, preferably on the back of a desktop PC.
- Use a different cable.
- If it is a bare drive in a USB enclosure or dock, try a different enclosure. If you moved the drive out of its original enclosure, put it back, because some enclosures present the disk differently and the partitions only make sense through that enclosure.
- Try another computer.
A surprising number of RAW drives come back to normal at this step.
Step 2: Check the drive's health before anything else
If the drive is failing, the steps that follow will stress it, and you may only get a limited number of hours of reads out of it. Read its SMART data: rising reallocated or pending sector counts, uncorrectable errors, or clicking noises mean you should copy data off immediately or, if the files are valuable, stop and contact a recovery service. Our guide on how to back up a failing hard drive explains how to do it with minimal stress on the drive.
Disk Detector is built for this moment. It checks the partition and file system, shows what is damaged before you format anything, and reads the drive's SMART health so you know whether you are dealing with a file system problem on a healthy drive or a drive that is failing. Its checks are read-only, so nothing on the drive is changed while you find out.
Step 3: Check for an unsupported file system
Ask where the drive came from. Drives formatted on a Mac (APFS or HFS+), a Linux PC (ext4), or by some TV recorders and security camera systems will show as RAW on Windows even though they are perfectly healthy. In that case, there is nothing to repair. Copy the files off on the original device, then reformat the drive in a format that works on both, such as exFAT. See NTFS vs exFAT vs FAT32 for help choosing.
Step 4: Recover the files, then rebuild the volume
If the drive is healthy, the connection is fine, and the file system was NTFS, exFAT or FAT32, the file system itself is damaged. You have two routes:
Recover first, then format (safest)
- Use file recovery software to scan the RAW drive and copy your files to a different drive. Never recover files onto the same drive. Disk Detector is a diagnostic tool and does not recover files; our separate product Drive Restorer does.
- Open the recovered files to check they are intact.
- Once your data is safe, format the RAW drive in Disk Management: right-click the partition, choose Format, pick the file system, and leave Perform a quick format ticked.
- Copy your files back.
Rebuild the file system in place (riskier)
Partition recovery tools can sometimes rebuild a damaged boot sector or partition table from a backup copy on the disk, making the drive readable again without copying everything. This can work well, but a mistake can make things worse. If the data matters, recover the files first, or work on a full disk image rather than the original drive.
What not to do
- Do not format to "see if it helps". A quick format makes recovery harder, and a full format overwrites every sector with zeros.
- Do not initialize the disk if Disk Management offers to.
- Do not run repeated repair attempts on a drive that clicks, disconnects or is getting slower.
- Do not recover files onto the RAW drive itself.
Preventing RAW drives in future
Most RAW drives are caused by a write being interrupted. Always use Eject before unplugging a USB drive, avoid moving external drives while they are busy, and use a surge protector or UPS for desktop PCs with important data. For removable drives, NTFS is more resilient to interrupted writes than exFAT or FAT32 because it keeps a journal of changes. And keep a backup: a RAW drive is a minor annoyance when there is another copy of everything on it.
Frequently asked questions
Can chkdsk fix a RAW drive?
Usually not. chkdsk reports that it is not available for RAW drives, because Windows cannot recognize any file system to check.
Does formatting a RAW drive delete my files?
A quick format replaces the file system, and a full format overwrites the data. Recover anything you need before formatting.
Why did my drive suddenly turn RAW?
Common causes are unplugging during a write, a power cut, a failing drive, a faulty USB enclosure or a file system Windows cannot read.
